Wwise SDK 2022.1.8
In Wwise, a secondary output designates any physical audio end-point that is not the regular TV audio output. The most common secondary outputs are the game controller speakers and headsets. The Secondary Output feature allows you to define a separate mix for each of these outputs, leaving the main speaker/TV mix unaffected. The same Wwise feature set applies to the secondary outputs as for the regular mix, without any particular restrictions except that the output targets controllers instead of the speaker/TV.
On the authoring side, you need to create new master busses to be able to define a different mix for an Audio Device. Then change the Audio Device ShareSet property on that new bus to point to a different device. Note that if you want to use an Audio Device plug-in created by a third party, you might need to create an Audio Device ShareSet of the right plug-in type first. Then the sounds can be routed normally to the new bus or any child bus. See Audio Devices for information on which Audio Device is available with Wwise.
Setting the Output Bus directly is the preferred method for sounds that are normally tied to only one secondary output instance. For example, player-initiated gunshots, tennis racket whacks, PDA sounds, gameplay feedback, and so on. However, you can use a User or Game Send to an Auxiliary Bus inside any other bus hierarchy. This is the preferred method if the same sound is going to be heard in multiple outputs and the TV at the same time, such as with a spy camera or announcements.
It is possible to play the same sound on multiple controllers and on TV at the same time, using the same source. On the design side, there is no knowledge of how many players might be playing the game. The bus hierarchy will be used as a template for routing for each output registered from the game. So, each output may have a different mix and Effect applied, depending on the sources played, as well as RTPC and Switch values active on the game objects. See an example of this in the Examples section below.
When outputting the same audio on many devices, such as the TV and a game controller, you will probably notice latency between the devices. This is unavoidable due to different hardware in the audio signal's path. On the controller side, the signal may have to travel through a wireless channel, which might give a different delay than for wired controllers. For the TV, once the signal is out of the console, it goes through a receiver and/or a TV, whose processors add a certain amount of delay. Since the delay produced by the AV setup is different for each system, it's not possible to synchronize sounds routed simultaneously to the speaker/TV and the game controllers. Your sound design may need to take this constraint into consideration.
In the case of multiple outputs of the same type (think, for example, a game controller speaker), it is necessary to discriminate between each instance of the devices. The regular
Listener/GameObject concept is used because it also allows specific listener/emitter routing. See Concept: Listeners for more information. It is the responsibility of the game programmer to associate the output device with a Listener using
AK::SoundEngine::AddOutput. The programmer must set the association between the listeners and game objects using
AK::SoundEngine::SetActiveListeners. Don't forget, you can specify multiple listeners if multiple devices should play this sound at the same time (see example below).
|Note: It is not necessary to have multiple listeners if there is only one output of a particular type (such as System, DVR). In this case, Wwise can rely on the routing specified in the Wwise project. This is also true for player-specific outputs (such as Game Controller Speaker and Communication) if the game is single-player. In other words, if there will only be one controller active in the game. Read more about listeners in Integrating Listeners.|
Note: In the case of player-devices, the game code is responsible for calling
These examples are written for the PS4, but can apply to all other platforms. Please check the documentation for the function
AK::SoundEngine::AddOutput. You can find a working example of multiple output management in the Integration Demo Sample, in the DemoMotion page (multi-player), and in the BGMDemo page (DVR/BGM management).
Note: These examples omitted the required
Code to get the UserIDs (PS4 only):
Sound on one game controller output:
Same sound on two different controllers:
Different sounds on two different controllers:
Same sound on one game controller output and on the TV:
Here's an example of adding a secondary output on Windows, namely the headphones:
|Note: On Windows, all devices are "System" devices. Therefore, adding a device means it is necessary to discriminate between them (see Setting up devices, listeners and game objects for multiple outputs for information). Consequently, we need a different listener.|